Concrete Floor Stripping & Removal in Oakley CA - a clean slab ready for its next floor
Old epoxy or paint peeling off your garage floor? We take it down to sound concrete so your next floor has something solid to hold.
- Repair checked first I look at whether a spot repair will do first.
- Testing before grinding If the old coating's makeup is unclear, we test before grinding.
- Steps laid out You see each step before the grinder ever starts.
- Prep for what's next We clean and prep the slab for your new floor.
- Licensed and insured.
- Free in-person estimates.
- We respond within 1 business day.
How can you tell an old floor coating needs to come off?
Catching a failing coating early often means a spot repair instead of stripping the whole floor, and less damage to the concrete underneath.
Coating peeling in sheets
If the coating lifts in sheets you can pull up by hand, it has usually lost its bond to the slab, and anything patched over it tends to peel too.
Finish lifting under tires
When the coating comes up where your car parks, warm tires are pulling a weak layer off the concrete. Left alone, the bare spots spread and soak up oil.
Bubbles or blisters underfoot
Raised bubbles usually mean moisture or a weak bond under the coating. The longer they sit, the more water and grit get underneath, which makes the next floor's prep harder.
Chips spreading across the floor
A few chips by the door may only need a spot repair. Bare patches showing up all over usually mean the coating is failing everywhere and it's time to strip it.
Old paint under new plans
Planning epoxy or polished concrete over old paint or sealer? A new floor only holds as well as what's under it, so the old layer usually comes off first.
Yellowed finish that won't clean up
An old coating that's gone cloudy or yellow and stays dull after cleaning is worn out. A fresh coat won't grab it well, so stripping often comes before recoating.
How our concrete floor stripping and removal works
When someone in Oakley calls about concrete floor stripping and removal, the first thing I look at is whether a smaller repair would do the job, because tearing off a coating that's mostly holding costs you time and money you don't need to spend. If there's any question about what's in the old coating, we get it tested before anyone grinds, since you don't want an unknown material turned into dust inside your house. Stripping itself means taking the old coating off by diamond grinding, shot blasting or a chemical stripper, and once it's off we clean and prep the bare slab, because removal alone doesn't leave concrete ready for a new floor. What moves the price and the schedule is mostly the size of the floor, what's on it now and what we find underneath, and your written estimate lays that out step by step.
Most stripping jobs end with a new floor going down, and the prep we just finished is what our epoxy floor coatings need to grip the slab. For shops, warehouses and businesses, the next step is usually commercial and industrial epoxy floor coatings made for heavier traffic.
What happens after you call about stripping a floor in Oakley?
Here's how a stripping job runs with us, from your first call to walking the finished floor together.
Call and set up a visit
Call (925) 503-1112 or use the form, then I come out to look at the floor, check the slab and hear what you want next.
Get your written estimate
I measure the floor and send a written estimate that lays out each step, including any testing the old coating needs before we grind.
We strip and prep the slab
Once you say yes, I lay out the steps so you can see them, then we take the coating off and prep the concrete properly.
Walk the floor together
If a new floor is part of the job, we put it down next. Either way, we walk the finished floor with you at the end.
Why Oakley homeowners call Ridgeline Oakley Epoxy Flooring
I look at your floor myself
I check your slab and write the estimate, and I'm on the install with our small crew and a crew lead.
Licensed and insured on your job
That counts when we're running grinders and heavy equipment inside your garage or shop.
Started in Oakley in 2023
I spent years lining up crews and schedules before starting here, so your job is planned out before anyone shows up.
Satisfaction guaranteed on every job
That's our promise on stripping work too. Call (925) 503-1112 or use the form on this page to get your estimate started.
Get a written plan for stripping your floor
Send the floor's size and anything you know about the old coating, and we'll reply within one business day. I'll come out for a free on-site estimate, with no obligation, and send it to you in writing.
Stripped and prepped floor examples
Browse these example photos of concrete floors being stripped, prepped and recoated to get a feel for what each stage of the work looks like.
Questions about stripping a concrete floor
Here are the questions Oakley homeowners and shop owners ask most about taking an old coating off concrete. If yours isn't here, call or send a message about your floor.
Do I need to remove my whole garage floor coating, or can it be spot repaired?
Not always, since one materials company's guide says that if 90% of the floor is bonded and solid, it's a spot repair rather than a removal project. Full removal is the right call when the bond is failing across the whole slab.
What is the best way to remove epoxy from a garage floor?
For a standard two- or three-car garage, diamond grinding is almost always the practical choice, while shot blasting suits warehouse slabs, loading docks and larger commercial floors. Grinding's tradeoff is silica dust, which harms the lungs, and a California safety rule requires a dust reduction system when powered tools grind concrete. Ask any crew you're considering how their equipment meets that rule.
How long does it take to strip a concrete floor?
One flooring cost guide puts a typical 1,000-square-foot area at one to three days for removal, including cleanup and prep for the next floor. Thick or layered coatings and any testing change that, so your estimate covers what your floor needs. Before work starts, move furniture and appliances out of the area, and covering doorways helps keep dust from spreading.
How much does it cost to strip an epoxy floor in Oakley?
There's no set price until I've seen the floor, because the size, the old coating and the slab under it all change the work. A spot repair costs less than stripping the whole floor, and the prep your next floor calls for matters too, so your written estimate breaks out each step.
Do I need a permit to strip a floor coating in Oakley?
Ask before work starts, because Oakley's Building Division asks owners to contact it before any project to learn whether it needs a permit. The city issues permits only to the property owner, an agent the owner authorizes, or a contractor licensed by the California State License Board. We check with the office that covers your address first, and if a permit is needed we can pull it as your licensed contractor or help you apply yourself.
What should I do if my old floor coating might contain asbestos or lead?
Get it tested before anyone grinds or blasts it, because one tool seller's guide says to stop for qualified testing and remediation whenever a coating may hold lead, asbestos or another hazardous material. If asbestos is found, the Bay Area Air Quality Management District must be notified at least 10 business days before a renovation that removes 100 square feet or more of it. A home in a building with four or fewer units may notify the district 72 hours ahead with an additional fee.
Get your old floor coating off the right way
Call (925) 503-1112 with your floor's size and what's on it now, and I'll know what to look for on the first visit.